revision date: may 02, 2012 page 1 of 3 overview this product specification defines the general use and performance parameters for amphenol?s musbr series of connectors. availability: series a right angle connectors ar e available now. verti cal pcb mount connectors will be available q3, 2012. mini-b and series mini-ab with right angle and vertical pcb tails are coming soon. right angle connectors mounted on a pcb with matching usb, cable headers or terminal blocks are available for all series. dust covers for enhanced mating area protection are also available. usage these connectors meet military shock & vibration levels and ip68 per iec 60529 in mated and unmated conditions. the connector system is desi gned to provide a standard usb interface for enclosures exposed to harsh environments. connectors mate with any standard usb 2.0 plug. achieves data rates up to 480 mb/s (usb 2.0). applications intended for use in applications such as: ? medical equipment ? microwave transmitters ? gps, positioning equipment ? military vehicles, radios, computers ? test equipment ? mobile entertainment systems ? traffic control & monitoring systems musbr rugged usb product specification s6056c rev 1.1 musbr-a111-30 series a, right angle standard profile about amphenol commercial products amphenol?s commercial connector products are used in a variety of end user applications including networking, telecom, server & computer, storage & hdd, consumer electronics and entertainment, professional audio & industrial & military/aerospace. related products musb/musbr options: with matching usb with cable header with terminal block with pcb for wiring musbr-a111-40 series a, right angle low profile
revision date: may 02, 2012 page 2 of 3 connector electrical characteristics parameter series a & b series mini-b & mini-ab current rating: 1.5a per contact 1.0a per contact contact resistance: 30 m ? max 50 m ? max insulation resistance: 1000 m ? min 100 m ? min dwv: 500v ac @ sea level 100v ac @ sea level connector mechanical characteristics thermal shock: 5 cycles @ -40 to +125 c physical shock: per eia364-27 condition h (11ms 30g) humidity: per eia364-31 condition c, method iii vibration: per eia364-28 per condition v, letter a salt spray: per eia364-26, 250 hrs process characteristics recommended soldering process: hand or wave soldering peaked at 260c for 8 seconds max. recommended torque for #4-40 or m3 panel mount screws: 0.45 to 0.65 nm (4 ? 5.75 in-lbs). recommended torque for #2-56 or m2.5 panel mount screws: 0.23 to 0.34 nm (2 - 3 in-lbs). solder tails suitable for pcb thickness of 1.52mm (.062?) mating cycles: 1500 (series a & b) 5000 (series mini-b & mini-ab) material requirements musbr connectors are rohs compliant. unless otherwise specified, the mate rials for each component shall be: ? contacts: phosphor bronze with 30? (0.76m) min gold over 50? (1.27m) min nickel ? housing: engineering thermoplastic, ul94v -0 rated, black. white for series b. ? shell: die cast zinc alloy, nickel plating temperature rise: meets the requirement of 30 c t operating temperature -40 to +105 c available documents drawing numbers: P-MUSBR-A111-xx musbr rugged series a, right a ngle pcb tail, thread, shell & dust cover options p-musbr-a511-xx musbr rugged series a, right angle, vertical pcb mount contact factory, authorized amphenol representative or website www.amphenolcanada.com for additional configurations quality test reports qtr9300491 qualification test report about amphenol commercial products amphenol?s commercial connector products are used in a variety of end user applications including networking, telecom, server & computer, storage & hdd, consumer electronics and entertainment, professional audio & industrial & military/aerospace. related products mdbr musbk mrjr 9 position connector shown mrjr-5380-01 shown right angle, pcb tail, 8 position rj45 musb-k152-30 series micro-ab right angle, pcb tail
amphenol canada corp. page 3 of 3 605 milner avenue toronto, ontario, canada, m1b 5x6 copyright ? amphenol corporation 2012 ? all rights reserved +1 416 291 4401 www.amphenolcanada.com this document contains proprietary information and such information may not be disclosed to others for any purpose or used for manufacturing purposes without written permission from amphenol canada corp. s6056c rev 1.1 product numbering system musbr - a 1 1 1 - 3 0 musbr connector series designation - rugged usb style a - receptacle series a, single termination 1 - right angle pcb tail 2 - right angle pcb tail, on pcb with right angle cable header, note 1 3 - right angle pcb tail, on pcb w ith matching usb termination, note 2 4 - right angle pcb tail, on p cb with terminal block(s), note 3 5 - vertical pcb tail 8 - right angle pcb tail, on pcb with vertical cable header, note 4 a - right angle pcb tail, on pcb for hand wiring e - right angle pcb, on pcb, with vertical usb termination, note 4 number of contacts 1 - standard 4 per port colour 1 - black - standard options 0 - no rear shield; shell with unified national thread, note 5 & 6 3 - with rear shield; shell with unified national thread, note 5 & 6 4 - low profile; with rear shield ;shell with unified national thread, note 5&6 m - with rear shield; shell with metric thread, note 5 & 7 n - no rear shield, shell with metric thread, notes 5 & 7 r ? low profile; with rear shield; shell with metric thread, note 5 & 7 dust cover options 0 - standard (no dust cover) 1 - with grey color dust cover (supplied bulk packed) 4 ? standard (no dust cover), note 8 5 - with black color dust cover (supplied bulk packed) unique special code no digit ? standard part defined by previous 10 digits 1 to 9 - unique special feature. note 9 notes 1) design of right angle cable header varies de pending upon the style. refer to drawing for details. 2) matching usb is the same usb series as the rugged connector 3) design of terminal blocks varies depending upon the style. refer to drawing for details. 4) vertical headers & vertical matching usb?s may not be readily available for all connector styles. 5) rear shield required for styles a, c & d with right angle pcb tails. rear shield optional for styles b & e with right angle pcb tails. no rear shie ld for any vertical pcb tail. 6) use #4-40 unc for styles a, c & d and #2-56 unc for styles b & e 7) metric thread - use m3 for styles a, c, & d and m2.5 for styles b & e 8) dust cover option code 4 is identi cal to code 0 and may be used for styles b & e only. 9) many unique features are readily available to suit customer requirements. consult with amphenol canada for details.
|
